Omnitron Systems Technology Network Card iConverter 2FXM User Manual

Management Options iConverter, Serial Agent  
Network Management  
1: Chassis and Module Management  
2: Set Module Name Preferences  
Management Module Preferences  
3: IP and Control Preferences  
4: SNMP Preferences  
iConverter 2FXM Plug-in Module QUICK START GUIDE  
The Omnitron iConverter® 2FXM Network Interface Device (NID)  
with integrated management provides Fast Ethernet  
(100BASE-FX) fiber-to-fiber media conversion.  
The 2FXM conforms to Ethernet in the First Mile (EFM) fiber  
standards to support Fiber-to-the-X (FTTX) Metropolitan and  
Enterprise LAN networks. Built-in Operation, Administration  
and Maintenance (OAM) functionality enables the 2FXM to  
operate as a managed demarcation point at the customer  
premises and network edge, offering service provisioning  
functions, such as Quality of Service and Bandwidth Control  
(rate-limiting) capabilities.  
5: Abandon Preference Changes  
6: Save Preference Changes  
7: Restore Factory Defaults  
8: Restart Management Module  
9: Other Networking Features  
Management Module Maintenance  
10: Firmware Update  
The 2FXM module can be managed using Omnitron’s NetOutlookTM SNMP Management  
Software, 3rd Party SNMP Client, Telnet or the Command Line Interface (CLI).  
11: Set Date/Time  
For more information, including the complete User Manual on the 2FXM Plug-in module,  
access Omnitron’s documentation download web page to view all relevant documents:  
IP Address = 192.168.1.220  
Chassis Number = 1  
Enter Choice, <H>elp, E<x>it >  
INSTALLATION PROCEDURE  
1) Configure DIP-Switches  
Figure D: Command Line Interface Menu Options  
2) Install Module in Chassis and Connect Cables  
3) Configure Module via Command Line Interface  
4) Verify Operation  
The CLI interface allows for the detailed configuration of the module. It is recommended  
to configure the module with an IP address associated with the attached network.  
Also, SNMP traphost address should be configured if the module is managed with an  
SNMP-based Management System. See the 2FXM User Manual for complete  
information.  
1) CONFIGURE DIP-SWITCHES  
Switch 1  
4) VERIFY OPERATION  
DIP-SWITCH BANK 1  
LED Function  
"Legend"  
Color  
Amber No power  
Chassis Power  
Off State  
On / Blinking State  
Once the module has been  
installed and configured per  
steps 1 - 3, verify the module  
is operational by viewing the  
LED indicators.  
Bank 2  
SW1 - PAUSE ENABLE  
Switch 8  
Power "Pwr"  
On: Module has power  
When the Pause Enable DIP-switch is in the  
LEFT “Off” position (factory default), the 2FXM  
disables the fiber ports’ ability to send and  
receive Pause frames during network  
congestion. Setting this DIP-switch to the  
RIGHT “On” position, enables the 2FXM to  
receive Pause frames from its link partner. This  
enables the 2FXM to stop transmitting traffic to  
its link partner and store incoming frames from  
the other port in the internal buffer until the  
congestion clears. If the internal buffer of the  
2FXM becomes congested, it will transmit a  
Pause frame to its link partner.  
On: Power available from  
installed Power Supply #X  
Switch 1  
Power Supply Status  
#X  
Amber  
Supply not installed Blinking: No power available  
from installed Power Supply #X  
Bank 1  
Port 1  
Switch 8  
On: Fiber link is active  
Blinking: Fiber Data Activity  
The Power LED indicates the Fiber Link Activity  
Green No Fiber Link  
Green Half-Duplex  
"P1"  
module is receiving power  
Port 1  
RIGHT  
LEFT  
Half/Full Duplex  
"FDX"  
Chassis Management  
Master/Slave  
"Msr/Slv"  
Port 2  
Fiber Link Activity  
"P2"  
Port 2  
Half/Full Duplex  
"FDX"  
On: Full-Duplex  
from the chassis.  
On: Chassis Master  
Blinking: Operating in OAM  
Mode  
The Fiber Optic link LEDs  
indicate the fiber optic  
connections have been  
established. Verify the Link  
Mode selection is set to Link  
Segment (LS). Until a stable  
link is established, leave the  
Link Mode configured for LS.  
Chassis Slave  
Green  
Mode  
On: Fiber link is active  
Blinking: Fiber Data Activity  
Green No Fiber Link  
Green Half-Duplex  
Figure A: DIP-Switch Locations  
On: Full-Duplex  
Figure E: LED Indicators  
SW2 - FIBER PORT 1 FULL/HALF DUPLEX  
Setting this DIP-switch to Half-Duplex “HDX” facilitates a connection that supports Half-  
Duplex. Setting this DIP-switch to Full-Duplex “FDX” facilitates a connection that  
supports Full-Duplex operation.  
After a Link presence is established, the Link Mode selection can be modified.  
Form 040-08940-002 D 12/07  
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618  
 

Miller Electric Welding System Spectrum 2050 User Manual
Milwaukee Power Screwdriver 2101 20 User Manual
Mr Coffee Coffeemaker 109041 User Manual
Nady Systems Stereo Amplifier SPM 835 User Manual
NEC Flat Panel Television S401AVT User Manual
New Media Technology Stereo System Omnia ONE Multicast User Manual
NordicTrack Home Gym NEL09940 User Manual
One for All TV Video Accessories 703988 User Manual
Optoma Technology Projector EP550 User Manual
Palm PDAs Smartphones 406 4454B US User Manual