Omnitron Systems Technology Network Card 10FL 2 User Manual

Power Adapter Notice:  
Switch Settings:  
1. When using in a stand-alone configuration, this product  
is intended to be used and must be used only with a  
Listed Direct Plug-In Power Unit marked “Class 2” and  
rated at 9Vdc, 1 Amp.  
“Termination” Switch: When attaching anywhere along  
a coax cable except at the end, the Termination Switch  
should be set to “Termination Out” (factory setting). When  
attaching to the end of a cable, it can be set to  
Termination In.” Note that when the switch is set to  
Termination In,” an external termination element must  
not be attached.  
FlexPointTM 10FL/2 User Instructions  
Description:  
The FlexPointTM family of converters supports the  
IEEE 802.3 and Ethernet Versions 1.0 / 2.0 standards.  
They convert among 10BASE-FL fiber, 10BASE-2  
thin coax and 10BASE-T twisted pair (UTP) media  
types.  
2. This product should always be used only with Omnitron  
Supplied Power Unit model number 9113-PS.  
LED Indicators:  
WARNING!  
Before installing and connecting the Power  
Adapter verify that the power on the unit is  
appropriate for your AC line voltage source.  
LED  
Color Description  
The FlexPoint 10FL/2 converts from 10BASE-FL fiber  
to 10BASE-2 coax. It uses ST fiber and BNC coax  
connector. The following models are described here:  
Power On  
Jabber  
Yellow Power applied  
Red  
Jabber condition  
Fiber Link  
Green Operational device detected at  
the far end of fiber.  
Mounting:  
Model Fiber Type  
Maximum Distance  
The Omnitron FlexPoint 10FL/2 can be solo-mounted using  
awall-mountingkit, orrack-mountedusinga5-positionspace-  
saver shelf, FlexRack 5, or a 14-position high-density  
FlexPoint Powered Chassis. When wall-mounting or shelf-  
mounting, connect the power adapter unit.  
Fiber Rx  
Coax Rx  
Collision  
Green Received data on fiber line.  
Green Received data on coax line.  
Yellow Collision detected  
4310 850 nm (multimode)  
2 km  
30 km  
5 km  
4311  
1310 nm (single-mode)  
4312 1310 nm (multimode)  
For metal ST fiber connector, add M before the ‘dash’  
in the Model Number. Example: 4310M-1, 4311M-0  
Technical Support:  
If you encounter problems in installing or maintaining  
this product, contact Omnitron Technical Support:  
Phone:  
Fax:  
Address: Omnitron Systems Technology, Inc.  
140 Technology Drive, #500  
When connecting the FlexPoint 10FL/2 at the end of a coax  
segment, attach the coax cable directly into the FlexPoint’s  
BNC coax connector. When connecting it along the coax  
line (not at the end), use a “T” connector to tap into the cable.  
The 10FL/2 provides a switch-selectable 50 ohm  
termination that allows easy termination of the coax  
cable. This function should be used only when the  
FlexPoint is connected at the end of a segment.  
(949) 250-6510  
(949) 250-6514  
Attach the fiber cables to the FlexPoint’s connectors. The  
FlexPoint’s transmit (Tx) must attach to the receive side on  
the device at the far end of the fiber and the receive (Rx)  
must attach to the transmit side.  
Note that the total length of the coax cable must not  
exceed 185 meters and the number of stations on the  
coax segment must not exceed 30 stations (per IEEE  
802.3 specification).  
Irvine, CA 92618 USA  
E-mail:  
URL:  
product to Buyer’s designated US address using  
Omnitron’s standard shipping method.  
Warning  
Notes:  
The operating description in this Instruction Manual is  
for use by qualified personnel only. To avoid electrical  
shock, do not perform any servicing of this unit other  
than that contained in the operating instructions, unless  
you are qualified and certified to do so by Omnitron  
Systems Technology, Inc.  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
_____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
____________________________  
Limitation of Warranty  
The foregoing warranty shall not apply to defects  
resulting from improper or inadequate use and/or  
maintenance of the equipment by Buyer, Buyer-supplied  
equipment, Buyer-supplied interfacing, unauthorized  
modifications or tampering with equipment (including  
removal of equipment cover by personnel not  
specifically authorized and certified by Omnitron), or  
misuse, or operating outside the environmental  
specification of the product (including but not limited to  
voltage, ambient temperature, radiation, unusual dust,  
etc.), or improper site preparation or maintenance.  
Caution  
All user-required operations can be performed without  
opening the unit. Never attempt to open or remove the  
cover or tamper with the unit.  
Warranty  
This product is warranted to the original purchaser  
against defects in material and workmanship for a period  
of TWO YEARS from the date of shipment. A LIFETIME  
warranty may be obtained by the original purchaser by  
REGISTERING this product with Omnitron within 90 days  
from the date of shipment. TO REGISTER, COMPLETE  
AND MAIL OR FAXTHE REGISTRATION PORTION OF  
THIS INSTRUCTION MANUAL TO THE INDICATED  
ADDRESS. During the warranty period, Omnitron will,  
at its option, repair or replace a product which is proven  
to be defective.  
No other warranty is expressed or implied. Omnitron  
specifically disclaims the implied warranties of  
merchantability and fitness for any particular purpose.  
Exclusive Remedies  
The remedies provided herein are the Buyer’s sole and  
exclusive remedies. Omnitron shall not be liable for any  
direct, indirect, special, incidental, or consequential  
damages, whether based on contract, tort, or any legal  
theory.  
For warranty service, the product must be sent to an  
Omnitron designated facility, at Buyer’s expense.  
Omnitron will pay the shipping charge to return the  
Form:040-04310-001C 11/07  
 

MTX Audio Car Speaker P2400 User Manual
Multi Tech Systems Network Card MultiModem ISI User Manual
Navman GPS Receiver F20 Europe User Manual
NETGEAR Security Camera 202 11288 02 User Manual
Nikon Digital Camera XX152 02 00 User Manual
Nilfisk ALTO Vacuum Cleaner 30 BATT PC XC User Manual
Omnimount TV Mount 10067 User Manual
Onkyo DVD Player DV S555 User Manual
ParaBody Fitness Equipment Free Weight Systems User Manual
ParaBody Home Gym PBF410A User Manual